Architectural Lighting Controls
Control-ready in minutes.
Wireless where it matters.
For architects, lighting designers and specifiers. Control sits inside the luminaire and next to the driver — clean ceilings, no control cabling, and light scenes that can be re-set as the space changes.
Member of DALI Alliance Zhaga Consortium Bluetooth SIG
The Three Lines We Lead With
D4i Bluetooth sensors + DALI D4i Converter
Sensor inside every luminaire, one converter per room. No gateway, no control cabling.
Wireless DMX / RGBWW control
Cove, linear and facade color scenes on the same mesh, fitted in a CV LED driver. R · G · B · CW · WW control.
DALI-2 occupancy + daylight sensors
Certified DALI-2 application & input devices, or standalone DALI-2 sensor with IR set-up.
One Bluetooth Mesh — from a single room to a whole floor.
Adjust the Lighting as Your Space Changes
Addressing + zones
Set up zones and DALI addressing from the LiteScape app. No laptop.
Scenes + schedules
Create light scenes and schedules, and re-set them as the space changes.
Sensor + daylight tuning
Adjust occupancy and daylight setpoints for each zone.
Firmware over the air
Keep devices on the mesh up to date from the app.
Make Lighting Part of the Experience
Hospitality
Hotel lobbies, restaurants and bars — sensing and scenes in every room, with color and tunable white for coves and accents.
Retail
Retail displays and linear accents with scenes that can be re-set as collections change.
Offices & classrooms
Sensing, scenes and daylight control in every room — without a central system.
Every room fully controlled — without a gateway.
For offices, classrooms, retail and hospitality rooms where the design calls for sensing, scenes and daylight control, but the budget and ceiling void leave no room for a central system. LiteScape D4i sensors and nodes fit inside the luminaire; one DALI D4i converter brings the room’s remaining drivers onto the same Bluetooth Mesh.
How a room goes together
Fit the luminaires
A LiteScape D4i sensor or node goes into each luminaire, powered from the D4i driver.
Add one converter
Drivers that dim together connect to a BLE–DALI D4i converter — up to 25 per converter.
Commission from the app
Zones, scenes, schedules and daylight setpoints from the LiteScape app. No laptop.
Bluetooth → DALI D4i Converter · Broadcast control
- SMBC1225AC BLE–DALI D4i Converter (D6/D8)

- SMBC1325DC BLE–DALI D4i Converter (D6/D8)

Bluetooth D4i Sensors · PIR
- IFS105D4i-CTB / CPHLowbay Round D4i PIR Motion / Photocell Sensor

- IFS108D4i-ZB20Lowbay Oval D4i PIR Motion / Photocell Sensor

- EFS106D4i-ZB18Highbay Round D4i PIR Motion / Photocell Sensor

Bluetooth D4i Sensors · Microwave
- IFS125D4i-CTB / CPHLowbay Round D4i Microwave / Photocell Sensor

- IFS128D4i-ZB20Lowbay Oval D4i Microwave / Photocell Sensor

- EFS126D4i-ZB18Highbay Round D4i Microwave / Photocell Sensor

Bluetooth D4i Node
- IFA115D4i-CTBD4i Node, Round (Screw Terminal)

Adds wireless control to a D4i luminaire that needs no sensor — the same app, the same mesh as the sensors and converters.
Scale up · D4i gateways and room controls
Bluetooth → DALI D4i Gateways
For larger rooms where each D4i driver needs its own address — up to 64 short addresses.
- MMUC1064-KOAC BLE–DALI D4i Gateway

- MMUC1264AC BLE–DALI D4i Gateway

- MMUC1206PAC BLE–DALI D4i Gateway with Push Button, super-compact

- MMUC1364DC BLE–DALI D4i Gateway, super-compact

Room controls
Join the same mesh with no control wiring — ideal for refurbishment.
- WP1018EBluetooth wall switches

- WP1214SBluetooth wall switches

- CP1014E / CP1214SBluetooth couplers — keep existing switches

- CS127-PIR / CS127-MWSStandalone Bluetooth ceiling sensors

Color and tunable white for the architectural details.
Cove, linear, facade and hospitality accent lighting on the same LiteScape Bluetooth Mesh as the DALI rooms. Each controller is paired with a constant-voltage LED driver, so color scenes are designed, scheduled and changed from the same app as the rest of the building.
The controller sits between the CV driver and the existing DMX512 fixtures — one driver, one controller, one run.
BLE-RGBWW controller
BLE → RGB+CCT tape-light controller
- 6-channel RGB+CCT, 2A per channel @ 24V
- 8kHz PWM, 16-bit effective dimming
- Bluetooth Mesh 5.0, OTA via LiteScape app
- Mounts in the CV driver’s low-voltage compartment
Full color and tunable white from one controller — no separate RGBWW decoder.
BLE–DMX bridge
BLE → DMX512 bridge
- Converts Bluetooth Mesh commands to DMX512-A
- DMX+ / DMX– / GND output, no load current on board
- Single all-in-one node, 1/2" KO mount
- Works alongside DALI zones in one LiteScape project
Brings existing DMX512 fixtures onto the mesh — no new low-voltage home runs.
Coves and linear runs, facade and landscape accents, retail displays, hotel lobbies, restaurants and bars — anywhere color and tunable white shape the space.
How JNODE fits a LiteScape project
One app, two protocols
DALI luminaires, CV tape light and DMX512 fixtures appear side by side in the LiteScape app.
No control enclosure
The node sits in the driver’s own low-voltage compartment, so the fixture keeps its footprint.
Same mesh, same scenes
Color and tunable-white channels join the zones, scenes and schedules already set for DALI.
Lumigear is our hardware partner for compatible LiteScape lighting-control products, including the CV enclosures used with JNODE.
Visit Lumigear (opens in a new tab)Certified sensor that fits any DALI-2 system.
For specifiers working on an open DALI-2 bus: each sensor registers as a certified DALI-2 input device, so it drops into LiteScape or any third-party DALI-2 controller — or runs a room on its own. Lowbay, highbay, external and ceiling formats cover offices, warehouses, car parks and corridors.
DALI-2 Sensor · PIR
- IFS05RD2-CTB / CPHLowbay Round PIR / Photocell + IR Receiver

- IFS08RD2-ZB20Lowbay Oval PIR / Photocell + IR Receiver

- EFS06RD2-ZB18Highbay PIR / Photocell + IR Receiver

- EFS24RD2-KOHighbay PIR / Photocell + IR Receiver

DALI-2 Sensor · Microwave
- IFS25RD2-CTB / CPHLowbay Round Microwave / Photocell + IR Receiver

- IFS28RD2-ZB20Lowbay Oval Microwave / Photocell + IR Receiver

- EFS26RD2-ZB18Highbay Microwave / Photocell + IR Receiver

Standalone DALI-2 ceiling-mount sensor
- CS27RD2-PIRStandalone PIR / Photocell + IR Receiver

- CS27RD2-MWSStandalone Microwave / Photocell + IR Receiver

One sensor, two modes
Fine-tune on site with the RM52 IR remote — adjust parameters, save presets A–D and send them to the sensor. No app or laptop needed.
| Parameter | Factory default |
|---|---|
| Motion detection | ON (occupancy) |
| Trim level (T1) | 100% |
| Hold time (T1) | 5 min |
| Standby dim level (T2) | 30% |
| Standby time (T2) | 60 min |
| Fade time | 1 s |
| Photocell | OFF |
| Photocell ON threshold | Low 5 fc / High 20 fc / CAL (calibrate to ambient) |
| Default sensor mode | Application device |
Plan Your LiteScape Project
LiteScape DALI 4 Flyer
Product lines, system architecture and model overview (PDF).
Download Flyer (PDF, opens in a new tab)Bring LiteScape into your next architectural project.
System design, luminaire integration or product selection — talk to the LiteScape team.