Architectural Lighting Controls

Control-ready in minutes.
Wireless where it matters.

For architects, lighting designers and specifiers. Control sits inside the luminaire and next to the driver — clean ceilings, no control cabling, and light scenes that can be re-set as the space changes.

Member of DALI Alliance Zhaga Consortium Bluetooth SIG

Product Lines

The Three Lines We Lead With

01 Small-to-Medium Projects

D4i Bluetooth sensors + DALI D4i Converter

Sensor inside every luminaire, one converter per room. No gateway, no control cabling.

LiteScape D4i sensors and BLE–DALI D4i converter
02 Color + Tunable White

Wireless DMX / RGBWW control

Cove, linear and facade color scenes on the same mesh, fitted in a CV LED driver. R · G · B · CW · WW control.

LiteScape BLE-RGBWW controller and BLE–DMX bridge
03 DALI-2 Basic Sensors

DALI-2 occupancy + daylight sensors

Certified DALI-2 application & input devices, or standalone DALI-2 sensor with IR set-up.

LiteScape DALI-2 application and input sensors
LiteScape BLE–DALI Architecture

One Bluetooth Mesh — from a single room to a whole floor.

Bluetooth Mesh · Up to 100 devices per network
Our core · Small-to-medium architecture projects, no gateway
LiteScape D4i sensor / node — inside the luminaire
D4i driver + luminaire — occupancy, daylight and scenes built into every fitting
BLE–DALI D4i Converter
Other drivers in the room dim together as one group — nothing to address
BLE–DALI D4i Gateway
Larger rooms — each D4i driver individually addressed
Wall switches · couplers · ceiling sensors
Scenes and occupancy across the whole mesh
Wireless DMX / RGBWW controller
Cove, linear and facade color scenes
Commissioned from the LiteScape App

Adjust the Lighting as Your Space Changes

  • Addressing + zones

    Set up zones and DALI addressing from the LiteScape app. No laptop.

  • Scenes + schedules

    Create light scenes and schedules, and re-set them as the space changes.

  • Sensor + daylight tuning

    Adjust occupancy and daylight setpoints for each zone.

  • Firmware over the air

    Keep devices on the mesh up to date from the app.

Compare two lighting scenes in the same space
Interior with the Daytime lighting scene applied
The same interior with the Evening lighting scene applied
LiteScape app with the Daytime scene selected
LiteScape app with the Evening scene selected

Illustrative interior shown with two app-configured scenes.

Architectural Applications

Make Lighting Part of the Experience

01 · D4i Bluetooth + DALI D4i Converter

Every room fully controlled — without a gateway.

For offices, classrooms, retail and hospitality rooms where the design calls for sensing, scenes and daylight control, but the budget and ceiling void leave no room for a central system. LiteScape D4i sensors and nodes fit inside the luminaire; one DALI D4i converter brings the room’s remaining drivers onto the same Bluetooth Mesh.

DALI-2 / D4i Parts 251–253 · Bus-powered · Zhaga Book 18 / 20

How a room goes together

  1. Fit the luminaires

    A LiteScape D4i sensor or node goes into each luminaire, powered from the D4i driver.

  2. Add one converter

    Drivers that dim together connect to a BLE–DALI D4i converter — up to 25 per converter.

  3. Commission from the app

    Zones, scenes, schedules and daylight setpoints from the LiteScape app. No laptop.

Bluetooth → DALI D4i Converter · Broadcast control

  • SMBC1225AC BLE–DALI D4i Converter (D6/D8)AC 220–240V · up to 25 devices
    SMBC1225 — AC BLE–DALI D4i Converter (D6/D8)
  • SMBC1325DC BLE–DALI D4i Converter (D6/D8)9.5–22.5VDC · up to 25 devices
    SMBC1325 — DC BLE–DALI D4i Converter (D6/D8)

Bluetooth D4i Sensors · PIR

  • IFS105D4i-CTB / CPHLowbay Round D4i PIR Motion / Photocell SensorScrew terminal / PH2.0 · bus-powered
    IFS105D4i-CTB / CPH — Lowbay Round D4i PIR Motion / Photocell Sensor
  • IFS108D4i-ZB20Lowbay Oval D4i PIR Motion / Photocell SensorZhaga Book 20 · bus-powered
    IFS108D4i-ZB20 — Lowbay Oval D4i PIR Motion / Photocell Sensor
  • EFS106D4i-ZB18Highbay Round D4i PIR Motion / Photocell SensorIP66, Zhaga Book 18 · bus-powered
    EFS106D4i-ZB18 — Highbay Round D4i PIR Motion / Photocell Sensor

Bluetooth D4i Sensors · Microwave

  • IFS125D4i-CTB / CPHLowbay Round D4i Microwave / Photocell SensorScrew terminal / PH2.0 · bus-powered
    IFS125D4i-CTB / CPH — Lowbay Round D4i Microwave / Photocell Sensor
  • IFS128D4i-ZB20Lowbay Oval D4i Microwave / Photocell SensorZhaga Book 20 · bus-powered
    IFS128D4i-ZB20 — Lowbay Oval D4i Microwave / Photocell Sensor
  • EFS126D4i-ZB18Highbay Round D4i Microwave / Photocell SensorIP66, Zhaga Book 18 · bus-powered
    EFS126D4i-ZB18 — Highbay Round D4i Microwave / Photocell Sensor

Bluetooth D4i Node

  • IFA115D4i-CTBD4i Node, Round (Screw Terminal)D6/D8 self-adaption · bus-powered
    IFA115D4i-CTB — D4i Node, Round (Screw Terminal)

Adds wireless control to a D4i luminaire that needs no sensor — the same app, the same mesh as the sensors and converters.

Scale up · D4i gateways and room controls

Bluetooth → DALI D4i Gateways

For larger rooms where each D4i driver needs its own address — up to 64 short addresses.

  • MMUC1064-KOAC BLE–DALI D4i GatewayAC 100–277V · up to 64 drivers
    MMUC1064-KO — AC BLE–DALI D4i Gateway
  • MMUC1264AC BLE–DALI D4i GatewayAC 220–240V · up to 64 drivers
    MMUC1264 — AC BLE–DALI D4i Gateway
  • MMUC1206PAC BLE–DALI D4i Gateway with Push Button, super-compactAC 220–240V · up to 6 drivers · 16 × 28 mm
    MMUC1206P — AC BLE–DALI D4i Gateway with Push Button, super-compact
  • MMUC1364DC BLE–DALI D4i Gateway, super-compact9.5–22.5VDC · up to 64 addresses · 16 × 28 mm
    MMUC1364 — DC BLE–DALI D4i Gateway, super-compact

Room controls

Join the same mesh with no control wiring — ideal for refurbishment.

  • WP1018EBluetooth wall switchesDC 3V battery
    WP1018E — Bluetooth wall switches
  • WP1214SBluetooth wall switchesAC 220–240V
    WP1214S — Bluetooth wall switches
  • CP1014E / CP1214SBluetooth couplers — keep existing switchesDC 3V battery or AC 220–240V
    CP1014E / CP1214S — Bluetooth couplers — keep existing switches
  • CS127-PIR / CS127-MWSStandalone Bluetooth ceiling sensorsAC 220–240V
    CS127-PIR / CS127-MWS — Standalone Bluetooth ceiling sensors
02 · Wireless DMX / RGBWW Control

Color and tunable white for the architectural details.

Cove, linear, facade and hospitality accent lighting on the same LiteScape Bluetooth Mesh as the DALI rooms. Each controller is paired with a constant-voltage LED driver, so color scenes are designed, scheduled and changed from the same app as the rest of the building.

Bluetooth Mesh 5.0 · DMX512-A · Lumigear CV enclosures

LiteScape BLE–DMX bridge wired between a Lumigear constant-voltage LED driver and existing DMX512 fixtures
How it is wired · North American version (AC 120–277V) · EU on request

The controller sits between the CV driver and the existing DMX512 fixtures — one driver, one controller, one run.

JNODE-RGBWX BLE-RGBWW controller
Model no. JNODE-RGBWX

BLE-RGBWW controller

BLE → RGB+CCT tape-light controller

  • 6-channel RGB+CCT, 2A per channel @ 24V
  • 8kHz PWM, 16-bit effective dimming
  • Bluetooth Mesh 5.0, OTA via LiteScape app
  • Mounts in the CV driver’s low-voltage compartment

Full color and tunable white from one controller — no separate RGBWW decoder.

JNODE-DMX BLE–DMX bridge
Model no. JNODE-DMX

BLE–DMX bridge

BLE → DMX512 bridge

  • Converts Bluetooth Mesh commands to DMX512-A
  • DMX+ / DMX– / GND output, no load current on board
  • Single all-in-one node, 1/2" KO mount
  • Works alongside DALI zones in one LiteScape project

Brings existing DMX512 fixtures onto the mesh — no new low-voltage home runs.

Applications

Coves and linear runs, facade and landscape accents, retail displays, hotel lobbies, restaurants and bars — anywhere color and tunable white shape the space.

How JNODE fits a LiteScape project

One app, two protocols

DALI luminaires, CV tape light and DMX512 fixtures appear side by side in the LiteScape app.

No control enclosure

The node sits in the driver’s own low-voltage compartment, so the fixture keeps its footprint.

Same mesh, same scenes

Color and tunable-white channels join the zones, scenes and schedules already set for DALI.

Lumigear is our hardware partner for compatible LiteScape lighting-control products, including the CV enclosures used with JNODE.

Visit Lumigear (opens in a new tab)
03 · DALI-2 Basic Sensors

Certified sensor that fits any DALI-2 system.

For specifiers working on an open DALI-2 bus: each sensor registers as a certified DALI-2 input device, so it drops into LiteScape or any third-party DALI-2 controller — or runs a room on its own. Lowbay, highbay, external and ceiling formats cover offices, warehouses, car parks and corridors.

IEC 62386 Part 103 / 351 · Occupancy + photocell + IR receiver

DALI-2 Sensor · PIR

  • IFS05RD2-CTB / CPHLowbay Round PIR / Photocell + IR ReceiverScrew terminal / PH2.0 · bus-powered
    IFS05RD2-CTB / CPH — Lowbay Round PIR / Photocell + IR Receiver
  • IFS08RD2-ZB20Lowbay Oval PIR / Photocell + IR ReceiverZhaga Book 20 · bus-powered
    IFS08RD2-ZB20 — Lowbay Oval PIR / Photocell + IR Receiver
  • EFS06RD2-ZB18Highbay PIR / Photocell + IR ReceiverIP66, Zhaga Book 18 · PSU 30mA
    EFS06RD2-ZB18 — Highbay PIR / Photocell + IR Receiver
  • EFS24RD2-KOHighbay PIR / Photocell + IR ReceiverIP66, external KO mount · AC 220–240V
    EFS24RD2-KO — Highbay PIR / Photocell + IR Receiver

DALI-2 Sensor · Microwave

  • IFS25RD2-CTB / CPHLowbay Round Microwave / Photocell + IR ReceiverScrew terminal / PH2.0 · bus-powered
    IFS25RD2-CTB / CPH — Lowbay Round Microwave / Photocell + IR Receiver
  • IFS28RD2-ZB20Lowbay Oval Microwave / Photocell + IR ReceiverZhaga Book 20 · bus-powered
    IFS28RD2-ZB20 — Lowbay Oval Microwave / Photocell + IR Receiver
  • EFS26RD2-ZB18Highbay Microwave / Photocell + IR ReceiverZhaga Book 18 · PSU 30mA
    EFS26RD2-ZB18 — Highbay Microwave / Photocell + IR Receiver

Standalone DALI-2 ceiling-mount sensor

  • CS27RD2-PIRStandalone PIR / Photocell + IR ReceiverCeiling / surface / trunking · PSU 30mA
    CS27RD2-PIR — Standalone PIR / Photocell + IR Receiver
  • CS27RD2-MWSStandalone Microwave / Photocell + IR ReceiverCeiling / surface / trunking · PSU 30mA
    CS27RD2-MWS — Standalone Microwave / Photocell + IR Receiver

One sensor, two modes

Choose a sensor mode to see how it works
Long-press TEST on the RM52 to switch to system mode
Press RESET to return to factory defaults
DALI bus LiteScape / DALI-2 ctrl not needed Sensor Luminaires

Mode 1 — the sensor detects occupancy and dims the luminaires on its own DALI bus. Mode 2 — the sensor reports to LiteScape or a DALI-2 controller, which drives the luminaires.

Fine-tune on site with the RM52 IR remote — adjust parameters, save presets A–D and send them to the sensor. No app or laptop needed.

DALI-2 sensor factory defaults
ParameterFactory default
Motion detectionON (occupancy)
Trim level (T1)100%
Hold time (T1)5 min
Standby dim level (T2)30%
Standby time (T2)60 min
Fade time1 s
PhotocellOFF
Photocell ON thresholdLow 5 fc / High 20 fc / CAL (calibrate to ambient)
Default sensor modeApplication device
RM52 IR remote
RM52 IR remote
Resources

Plan Your LiteScape Project

LiteScape DALI 4 Flyer

Product lines, system architecture and model overview (PDF).

Download Flyer (PDF, opens in a new tab)

Product Documentation

Find technical information for compatible controls.

View Product Documents

Bring LiteScape into your next architectural project.

System design, luminaire integration or product selection — talk to the LiteScape team.

LiteTrace Brands
2006Founded in Maryland, USA
4MBluetooth mesh nodes deployed
4,800+Buildings on Keilton+autani
600+Autani customers